The most common reason a sauna quote changes after the fact is that nobody opened the distribution board first. Here is what to check before you commit to anything.
Almost every unpleasant surprise in a sauna project traces back to electricity. The cabin arrives, the joinery goes in, and then somebody discovers the board cannot carry the heater. It is entirely avoidable with a ten-minute check.
Sizing the heater
Start with internal volume: width × depth × height in metres. Then adjust upward for every surface that absorbs rather than reflects heat.
| Feature | Add to effective volume |
|---|---|
| Glass door | +1.0 m³ |
| Full glass wall | +2.0 to 3.0 m³ |
| Uninsulated external wall | +1.2 m³ per wall |
| Tiled or stone surface inside cabin | +1.0 m³ per wall |
| Ceiling above 2.2 m | Recalculate actual volume |
A 2.0 × 2.0 × 2.1 m cabin is 8.4 m³. Add a glass door and it behaves like 9.4 m³, so you want a 9 kW heater rather than the 8 kW the raw figure suggested.
Supply by heater size
| Heater | Suits | Supply |
|---|---|---|
| 1.6 - 2.4 kW (infrared) | Any infrared cabin | 13A socket, dedicated circuit |
| 4.5 kW | Up to ~6 m³ | Single phase, 25A |
| 6.0 kW | 6 - 8 m³ | Three phase preferred |
| 8.0 - 9.0 kW | 8 - 12 m³ | Three phase |
| 10.5 - 15 kW | 12 - 18 m³ | Three phase, dedicated |
Checking your board before you commit
Three things to establish, in order:
Is three phase present? Look at the main incomer. Three live conductors rather than one, and a board arranged in three banks. Villas in newer Dubai communities frequently have it; older properties and most apartments do not.
Is there a spare way? Even with three phase available, you need physical space in the board for another breaker. Boards fill up, particularly where a pool or a garden supply was added later.
How far is the board from the sauna? This is the cost. A run within the same room is trivial. A run from a board in the garage to a basement on the far side of the villa, through finished walls, is real money.
What the installation must include
A dedicated circuit with correctly rated protection, RCD protection, cable sized for the load and the run length, and a heat-rated isolator positioned outside the cabin where it can be reached. The control panel goes outside the hot zone unless it is a model specifically rated for internal mounting. Everything is earthed and bonded properly.
This is licensed electrical work. In a Dubai villa it is also the part a future buyer's surveyor will look at, so it is worth having documentation at handover — which is why we issue a wiring diagram and commissioning sheet as standard.
If the supply is the obstacle
An infrared cabin sidesteps the problem entirely on a standard socket. It is a different experience rather than a lesser one, and for apartments it is usually the only workable answer. For traditional cabins, see Finnish sauna installation and heater supply and replacement.
Common questions
How many kW does a sauna heater need?
Roughly 1 kW per cubic metre of cabin volume, then add for cold surfaces. A glass door adds about one cubic metre equivalent; a full glass wall adds considerably more; an uninsulated external or tiled wall adds again. Calculate from measured internal dimensions including ceiling height, because volume grows faster than floor area suggests.
When do I need three-phase supply?
Generally above 4.5 kW. A 4.5 kW heater will run on a single-phase 25A circuit, which covers cabins up to about 6 cubic metres. From 6 kW upward, three phase is the norm, and above 9 kW it is effectively mandatory.
How do I know if my villa has three phase?
Open the distribution board cover and look at the main incomer. A single-phase supply has one live conductor plus neutral; three phase has three lives, and the board is usually visibly wider with breakers arranged across three banks. If you are unsure, photograph the board and send it to us — we can usually tell immediately.
What does it cost to add a three-phase circuit?
Between AED 4,000 and 12,000 in most villas, driven almost entirely by the cable run distance from the board to the sauna and how much chasing or containment is required. If three phase already reaches the board and there is a spare way, it is at the low end.
Does an infrared sauna need special wiring?
No, and that is its main practical advantage. Most cabins draw 1.6 to 2.4 kW and run from an ordinary 13A socket on a dedicated circuit. No load increase, no three phase, no application to anybody.